Straight veneer wireless sheet patchwork machine (automatic airbag type) LS-1800

Highlights: high sensitivity air pressure components with electronic proportional valve, control more accurate and more flexible.

Seam machine use description:

Straight veneer wireless sheet stitching machine is suitable for splicing solid wood sheets of furniture desktop, kitchen cabinet panel, door skin and decorative plywood. Changing the traditional sewing machine, the straight veneer wireless sheet sewing machine uses special heating and feeding mechanical structure to splice,

Enables the wood sheets to be tightly bonded and spliced without gaps. It can effectively improve the work production efficiency, reduce the sanding of the rear section and reduce the cost.

Unit description:

Splicing thickness range: 0.35~2.0mm

Splicing width range: 40 ~ infinite width

Splicing length range: 400 ~ infinite

Splicing speed: 5~50 M/min

Table height: 920mm

Splicing temperature: 100~220 ℃

Required pressure: 5kgf/c ㎡

Total Electricity: Approx8KW

Appearance size: 2100mm * 2100mm * 1700mm

Features:

* Use special cylinder precise control chain pressure

* Mechanical design fully complies with safety regulations.

* Built-in plastic box can be fine-tuned high-speed motor drive

* additional automatic cooling system to extend the use of glue time

* The upper base uses cylinder and linear guide rail for precise control and positioning

* The cloth glue adjustment piece can adjust the glue amount of the wood skin edge in time.

* The total power consumption is low and the heating section is narrow, effectively reducing the amount of wood skin deformation

* Sturdy and stable body design to ensure that the body is stable and does not vibrate when splicing

* The upper and lower heat-conducting strips are all made of chrome-plated material, making cleaning and maintenance easier.

* The feeding section is equipped with a reflective photoelectric sensor to accurately align the spliced veneer.

* Suitable for splicing of longitudinal solid wood veneer, which is different from traditional sewing machine

* The use of thermosetting glue can improve the splicing effect and effectively avoid the glue line at the splicing place.

* The glue coating auxiliary guide block improves the glue coating effect to make the feeding smoother, and the height can also be adjusted according to the thickness of the wood skin.

* Built-in automatic gluing system, can be efficient in the wood edge evenly glued, saving manpower and time to improve production efficiency

* The special angle design roller is more stable than the traditional roller to ensure the splicing yield.

* The upper and lower transmission chains use frequency converters to drive the gear motor to control the running speed, and the lower transmission chain uses wear-resistant guide rails to extend the service life

* The special engineering plastic transmission chain replaces the traditional stainless steel chain, effectively reducing the deformation caused by the high temperature of the heating block when the wood skin is spliced, indicating that it can solve the pollution situation

* The heater uses a solid-state relay to replace the traditional electromagnetic switch, and the temperature contact is precisely controlled without spark generation. The electromagnetic interference is smaller than the traditional electromagnetic switch and the service life is longer

* The man-machine interface is simple to use and easy to operate

Man-machine interface:

* Centralized start system, including feeding speed, splicing start/stop, heating start and temperature setting and other functions.

* Electric heating tube heating/fault can be displayed by the screen, so that the operator is easy to know the fault and troubleshooting

Feeding table:

* Upper and lower crawler conveyor, frequency conversion drive feeding speed 5~50 m/min.

* Stainless steel work surface, constant table height 920mm.

* The chain plate is made of engineering plastics, and the chain is imported from Japan.

Splicing temperature:

* Splicing temperature control range is 100 ~ 220C.

* The whole machine adopts Japanese electric heating tube and heat sensing probe, with stable heating and high temperature control sensitivity.

* The upper and lower central heat conduction plates make the splicing flatter.

Feed roller:

* The feeding pressure wheel is driven by photoelectric induction, which makes the feeding synchronous.

* The angle of the feed pressure wheel can be fine-tuned to make the sheet splice better.

adhesive cloth system

1. The plastic barrel is made of aviation aluminum as a whole with precision machining to ensure sealing and durability.

2. The cloth glue runs through the man-machine interface control, and the gear transmission glue barrel passes through the 45-degree cloth glue plate to carry out the wood skin gluing action, and the glue amount can be fine-tuned.

Randomly equipped with: * cooling machine * 1 & toolbox * 1 & release agent * 1 & instruction manual * 1